//初始化文件格式说明
//	每一行表示一条命令
//	每一行的第一个字节为命令字节，第二个字节为长度字节，后面跟上对应长度的值，如果长度为0，不需要再跟上值
//              如果一行已//开始，表示注释
//              禁止在命令行内添加注释
//延时设置：特殊情况，两个0xfe, 0xfe 表示延迟,
//	例如  0xfe, 0xfe, 120, 表示延迟120毫秒 
//通讯方式：3线9bit	u8cmd, u8size, u8val,
//	例如  0xC1,1, 0x3F, 表示寄存器0xC1， 1个字节，0x3f值
//	例如  0x29,0, 表示寄存器0x29， 0个字节，无值
//通讯方式：3线16bit	u16cmd, u16size, u16val,
//	例如  0xC301, 0x01, 0x22, 表示寄存器0xC301， 1个字节，0x22值
//	例如  0x1101, 0x00, 表示寄存器0x1101， 0个字节，无值
//注意1：必须配置通讯IO：SPI_CS、SPI_SDA、SPI_SCK
//注意2：LCD_RST可选配置，根据硬件设置，如RC复位则不需要配置rst，0xFF表示不存在PIN

0xF0,5, 0x55,0xaa,0x52,0x08,0x00,
0xF6,2, 0x5a,0x87,
0xC1,1, 0x3F,
0xCD,1, 0x25,
0xC9,1, 0x10,
0xF8,1, 0x8A,
0xAC,1, 0x65,
0xA7,1, 0x47,
0xA0,1, 0x99,
0x86,4, 0x99,0xA3,0xA3,0x41,
0x87,3, 0x04,0x03,0x66,
0xFA,4, 0x08,0x08,0x00,0x04,
0xA3,1, 0x6E,
0xFD,3, 0x28,0x3C,0x00,
0x9A,1, 0x6d,
0x9B,1, 0x44,
0x82,2, 0x22,0x22,
0xB1,1, 0x10,
0x7A,2, 0x0F,0x13,
0x7B,2, 0x0F,0x13,
0x69,7, 0x14,0x22,0x14,0x22,0x44,0x22,0x08,
0x6B,1, 0x07,
0x60,8, 0x38,0x0C,0x12,0x64,0x38,0x0B,0x12,0x64,
0x61,8, 0x33,0xC2,0x6A,0x39,0xB3,0xC9,0x52,0x52,
0x62,8, 0xB3,0xC9,0x52,0x52,0x33,0xC2,0x6A,0x39,
0x63,8, 0x38,0x0A,0x12,0x64,0x38,0x09,0x12,0x64,
0x64,16, 0x38,0x08,0x03,0xC0,0x03,0x03,0x38,0x06,0x03,0xc2,0x03,0x03,0x12,0x64,0x12,0x64,
0x65,16, 0x38,0x04,0x03,0xc4,0x03,0x03,0x38,0x02,0x03,0xc6,0x03,0x03,0x12,0x64,0x12,0x64,
0x66,16, 0x83,0xD5,0x03,0xC9,0x03,0x03,0x83,0xD5,0x03,0xc9,0x03,0x03,0x52,0x52,0x52,0x52,
0x11,0, 
0xfe, 0xfe, 120,
0x29,0,